The mechanical state of bolted joints in skewed girder sections of steel box girder bridges is complex, posing a key technical challenge in bridge design and construction. Based on the construction project of the prestressed concrete steel box girder bridge over the Beijing-Harbin expressway on the Qinhuangdao section of G102 national highway, simulation analysis and linear monitoring technologies were adopted to obtain the internal stress variation law of high-strength friction bolt groups in skewed girder sections. A mechanical model of high-strength friction bolt groups in skewed girder sections was established using ANSYS finite element software, and the deformation characteristics of skewed girder sections under different connection modes were analyzed, the optimal connection mode was obtained, and the dynamic characteristics of high-strength friction bolt groups were revealed. The dynamic load data show that the most unfavorable positions of the bolt group are the 5th and 15th columns. Under dynamic load, the maximum shear stress of the high-strength friction bolt group presents an approximately saddle-shaped- 引用格式:冯忠居,于明威,张聪,等.冲刷场地地震波形对大直径变截面单桩时程响应的影响［J］.河北大学学报(自然科学版),2026,46(4):337-348.引用格式:杨三强,李成旺,刘琦,等.钢箱梁桥斜交梁段栓接处动力学特性与仿真分析［J］.河北大学学报(自然科学版),2026,46(4):359-366.DOI:10.3969/j.issn.1000-1565.2026.04.003钢箱梁桥斜交梁段栓接处动力学特性与仿真分析杨三强,李成旺,刘琦,高毅松,刘娜(河北大学 建筑工程学院,河北省基础设施防灾减灾与智能评估重点实验室,河北 保定 071002)摘 要:钢箱梁桥斜交梁段栓接处受力状态复杂,是桥梁设计与施工面临的关键技术难题. 依托G102线秦皇岛上跨京哈高速公路预应力混凝土钢箱梁桥建设项目,采用仿真分析技术与线形监测技术,获取了斜交梁段高强度摩擦型螺栓群内应力变化规律;借助ANSYS有限元软件构建了斜交梁段高强度摩擦型螺栓群力学模型,分析了不同连接方式下的斜交梁段变形特征,得到了最优连接方式,揭示了高强度摩擦型螺栓群动力学特性. 动荷载数据显示,螺栓群不利受力位置为第5列、第15列;螺栓群在受到动荷载时,高强度摩擦型螺栓群剪应力最大值近似马鞍形分布,其主要特征是螺栓群两侧剪应力最大、中间剪应力最小、从螺栓群两侧向中间递减. 数值仿真分析结果表明,相同荷载条件下铆接的剪应力最大值约为高强度摩擦型螺栓连接的177%,焊接的应力最大值约为高强度摩擦型螺栓连接的440%,证实了栓接为最优连接方式.研究结果对钢箱梁桥螺栓群结构的设计、施工和监测具有重要的科学依据和工程参考.关键词:钢箱梁;连接方式;高强度摩擦型螺栓群;数值仿真;动力学特性中图分类号:U441 文献标志码:A 文章编号:1000-1565(2026)04-0359-08DOI:10.3969/j.issn.1000-1565.2026.04.003Dynamic characteristics and simulation analysis of bolted joint of skew girder section of steel box girder bridgeYANG Sanqiang, LI Chengwang, LIU Qi, GAO Yisong, LIU Na (Key Laboratory of Infrastructure Disaster Mitigation and Intelligent Assessment of Hebei Province, College of Civil Engineering and Architecture, Hebei University, Baoding 071002, China)Abstract:The mechanical state of bolted joints in skewed girder sections of steel box girder bridges is complex, posing a key technical challenge in bridge design and construction. Based on the construction project of the prestressed concrete steel box girder bridge over the Beijing-Harbin expressway on the Qinhuangdao section of G102 national highway, simulation analysis and linear monitoring technologies were adopted to obtain the internal stress variation law of high-strength friction bolt groups in skewed girder sections. A mechanical model of high-strength friction bolt groups in skewed girder sections was established using ANSYS finite element software, and the deformation characteristics of skewed girder sections under different connection modes were analyzed, the optimal connection mode was obtained, and the dynamic characteristics of high-strength friction bolt groups were revealed. The dynamic load data show that the most unfavorable positions of the bolt group are the 5th and 15th columns. Under dynamic load, the maximum shear stress of the high-strength friction bolt group presents an approximately saddle-shaped- 收稿日期:2025-02-21;修回日期:2026-04-09 基金项目:河北省高等学校科学技术研究项目(CXY2024012);河北省交通运输厅科技项目(202312;202305) 第一作者:杨三强(1980—),男,河北大学教授,博士生导师,主要从事桥梁监控、公路路基和路面材料方向研究.E-mail: ysq0999@163.com 第4期杨三强等:钢箱梁桥斜交梁段栓接处动力学特性与仿真分析河北大学学报(自然科学版) 第46卷distribution, which is mainly characterized by the maximum shear stress at both sides of the bolt group and the minimum shear stress in the middle, decreasing gradually from both sides to the middle of the bolt group. The numerical simulation results show that under the same load conditions, the maximum shear stress of riveted connections is about 177% of that of high-strength friction bolted connections, and the maximum stress of welded connections is about 440% of that of high-strength friction bolted connections, confirming that bolted connection is the optimal connection mode. The research results provide important scientific basis and engineering reference for the design, construction and monitoring of bolt group structures in steel box girder bridges.
YANG Sanqiang
,
LI Chengwang
,
LIU Qi
,
GAO Yisong
,
LIU Na
. Dynamic characteristics and simulation analysis of bolted joint of skew girder section of steel box girder bridge[J]. Journal of Hebei University(Natural Science Edition), 2026
, 46(4)
: 359
-366
.
DOI: 10.3969/j.issn.1000-1565.2026.04.003
[1] 武强.螺栓群受力不均匀时承载力分析[J].科技情报开发与经济, 2012, 22(4): 138-140.DOI:10.3969/j.issn.1005-6033.2012.04.060.
[2] 张文元,扈玥昕.钢结构中高强螺栓连接的数值模拟方法[J].哈尔滨工业大学学报, 2014, 46(12): 8-14.DOI:10.11918/j.issn.0367-6234.2014.12.002.
[3] He P, Fan Z Q, Yu X Y, et al. Influence of the axial position of the external load on the mechanical behavior of the bolted lap joint with different materials[J]. Mech Ind, 2019, 20(6): 623. DOI:10.1051/meca/2019066.
[4] Ahmed G H, Aziz O Q. Influence of intensity & eccentricity of posttensioning force and concrete strength on shear behavior of epoxied joints in segmental box girder bridges[J]. Constr Build Mater, 2019, 197: 117-129. DOI:10.1016/j.conbuildmat.2018.11.220.
[5] Ren Y Z, Wang B, Li Y Q, et al. New research for the distortion of steel box girders with inner solid diaphragms[J]. Adv Struct Eng, 2019, 22(14): 3026-3041. DOI:10.1177/1369433219856754.
[6] 田林杰,赫中营,孙鹏辉. 波纹钢腹板钢箱组合梁动力特性及参数分析[J].中国科技论文, 2023, 18(10): 1122-1127. DOI:10.3969/j.issn.2095-2783.2023.10.010.
[7] 李运生, 王慧佳, 张彦玲. 螺栓缺失对摩擦型高强螺栓传力性能的影响[J].广西大学学报(自然科学版), 2013, 38(4): 823-831. DOI:10.13624/j.cnki.issn.1001-7445.2013.04.035.
[8] 沈浩,蒋勐辉,王梓滔,等.钢桁梁桥典型节点高强螺栓受力影响因素分析[J].南京工业大学学报(自然科学版), 2020, 42(3): 373-379.DOI:10.3969/j.issn.1671-7627.2020.03.014.
[9] 李海岗.摩擦型高强度螺栓孔径及拼接板厚度对拼接节点传力性能的影响[J].山东理工大学学报(自然科学版), 2018, 32(6): 20-23. DOI:10.13367/j.cnki.sdgc.2018.06.005.
[10] 李向阳.钢箱梁U肋与桥面板深熔焊技术及抗疲劳性能研究[J].桥梁建设, 2020, 50(6): 45-52.DOI:10.3969/j.issn.1003-4722.2020.06.007.
[11] 程海根,刘祥基.钢桥节点的腐蚀磨损交互作用研究[J].钢结构, 2017, 32(7): 111-114. DOI:10.13206/j.gjg201707022.
[12] Wang D, Zhang Z S. A four-parameter model for nonlinear stiffness of a bolted joint with non-Gaussian surfaces[J]. Acta Mech, 2020, 231(5): 1963-1976. DOI:10.1007/s00707-020-02635-5.
[13] 陈明,刘梦星,刘沐宇.钢箱梁斜交节点动力响应与疲劳损伤演化[J].桥梁建设, 2022, 52(1): 16-19.DOI:10.3969/j.issn.1003-4722.2022.01.003.
[14] 刘浩,丁凤鸣,朱华,等.冷弯薄壁型钢高强螺栓连接剪力传递性能研究[J].工程与建设, 2022, 36(1): 16-19. DOI:10.3969/j.issn.1673-5781.2022.01.006.
[15] 彭涛,田仲初,张建仁,等.基于多目标优化的混凝土斜拉桥静动力有限元模型修正[J].振动与冲击, 2018, 37(21): 108-116. DOI:10.13465/j.cnki.jvs.2018.21.016.
[16] 杨三强,康义彤.钢箱梁桥腹板螺栓群偏心剪切力学仿真分析[J].铁道工程学报, 2023, 40(5): 58-63. DOI:10.3969/j.issn.1006-2106.2023.05.009.
[17] 康义彤.偏心荷载下钢箱梁段连接处受力分析及传力机理研究[D].保定:河北大学, 2023.
[18] 赵磊,刘刚,刘鹏.钢箱梁桥栓焊组合连接动力学特性试验研究[J].铁道工程学报, 2025, 42(2): 56-62.DOI:10.3969/j.issn.1006-2106.2025.02.009.
[19] 杨三强,何伟,吴浩楠,等.不同轮压与厚度下的半刚性橡胶沥青路面结构受力变形与仿真分析[J].河北大学学报(自然科学版), 2019, 39(6): 573-578. DOI:10.3969/j.issn.1000-1565.2019.06.003.
[20] 杨三强,张丹,黄井勇,等.连续变截面箱梁主墩0号块复杂受力模式与力学仿真分析[J].河北大学学报(自然科学版), 2024, 44(3): 225-234. DOI:10.3969/j.issn.1000-1565.2024.03.001.
[21] 张宇,陈开利,王天亮.钢箱梁桥拼接节点力学行为与疲劳性能研究[J].土木工程学报, 2023, 56(8): 78-87.DOI:10.3969/j.issn.1000-131X.2023.08.008.
[22] 方志,张国刚,唐盛华,等.混凝土斜拉桥动力有限元建模与模型修正[J].中国公路学报, 2013, 26(3): 77-85. DOI:10.19721/j.cnki.1001-7372.2013.03.008.
[23] 李宏年,赵欣欣,张翔.大跨度钢箱梁桥高强螺栓连接受力机理与数值模拟[J].中国公路学报, 2023, 36(5): 67-78.DOI:10.3969/j.issn.1001-7372.2023.05.006.
[24] 周林仁,欧进萍.斜拉桥结构模型修正的子结构方法[J].振动与冲击, 2014, 33(19): 52-58. DOI:10.13465/j.cnki.jvs.2014.19.009.
[25] 陈常松,刘灿,董道福.钢桁梁公路斜拉桥主梁刚度等效研究[J].中外公路, 2015, 35(5): 163-166. DOI:10.14048/j.issn.1671-2579.2015.05.036. (
