Loading...

Table of Content

    25 January 2025, Volume 45 Issue 1
    Effect of axial air gap asymmetric fault on the characteristic of electromagnetic torque in generators
    HE Yuling, FU Zixiang, DAI Derui, BAI Honghua, HUANG Weiling
    2025, 45(1):  1-9.  DOI: 10.3969/j.issn.1000-1565.2025.01.001
    Asbtract ( 89 )   PDF (1518KB) ( 65 )  
    References | Related Articles | Metrics
    Air gap eccentricity is a common mechanical fault in generators, the different operating parameters under air gap eccentricity will have an impact on the electromagnetic characteristics of generators. Previous researches mainly focused on the influence of axial air gap uniform eccentricity on the electromagnetic torque fluctuation characteristic. However, rare studies have considered the effects of variations in the axial air gap non-uniform eccentricity(inclination eccentricity). As a supplement, this paper comprehensively analyzes the effect of key operating parameters on electromagnetic torque characteristic in- DOI:10.3969/j.issn.1000-1565.2025.01.001轴向气隙非对称故障对发电机电磁转矩特性的影响何玉灵1,2,付滋翔1,代德瑞1,白洪华3,黄伟灵3(1.华北电力大学 机械工程系,河北 保定 071003;2.华北电力大学 苏州研究院,江苏 苏州 215123;3.浙江振兴阿祥集团,浙江 湖州 313000)摘 要:气隙偏心是发电机中常见的一种机械故障,气隙偏心下不同运行参数将对发电机的电磁特性造成影响.已有研究主要关注轴向气隙均匀偏心对电磁转矩波动的影响,较少关注轴向气隙非均匀偏心(倾斜偏心)所造成的影响.作为补充,该文全面分析了倾斜偏心下关键运行参数差异对发电机电磁转矩波动特性的影响.其中,关键运行参数主要包括倾斜偏心程度及发电机负载差异.整体工作以一台5 kVA的故障模拟发电机为研究对象,通过实验验证了理论分析和有限元分析得到的结果.结果表明:倾斜偏心会为电磁转矩带来额外的二倍频成分,且随着倾斜偏心角度的增大,电磁转矩的直流分量和二倍频成分都增大;随着负载的增加,发电机电磁转矩波动程度加剧,且直流分量和二倍频成分也将增大.关键词:发电机;负载差异;气隙非对称;电磁转矩中图分类号:TM311 文献标志码:A 文章编号:1000-1565(2025)01-0001-09Effect of axial air gap asymmetric fault on the characteristic of electromagnetic torque in generators HE Yuling1,2, FU Zixiang1, DAI Derui1, BAI Honghua3, HUANG Weiling3(1. Department of Mechanical Engineering, North China Electric Power University, Baoding 071003, China; 2. Suzhou Research Institute, North China Electric Power University, Suzhou 215123, China; 3. Zhejiang Zhenxing A Xiang Group Co., Ltd., Huzhou 313000, China)Abstract: Air gap eccentricity is a common mechanical fault in generators, the different operating parameters under air gap eccentricity will have an impact on the electromagnetic characteristics of generators. Previous researches mainly focused on the influence of axial air gap uniform eccentricity on the electromagnetic torque fluctuation characteristic. However, rare studies have considered the effects of variations in the axial air gap non-uniform eccentricity(inclination eccentricity). As a supplement, this paper comprehensively analyzes the effect of key operating parameters on electromagnetic torque characteristic in- 收稿日期:2024-03-29;修回日期:2024-05-07 基金项目:国家自然科学基金资助项目(52177042);河北省自然科学基金资助项目(E2022502003;E2021502038);中央高校基本科研业务费专项基金资助项目(2023MS128);河北省第三批青年拔尖人才支持计划([2018]-27);河北省高层次人才项目(B20231006);苏州市社会发展科技创新项目(SS202134);河北省研究生创新能力培养项目(CXZZBS2023149);南太湖精英计划创新人才团队项目 第一作者:何玉灵(1982—),男,华北电力大学教授,博士生导师,博士,主要从事电站设备状态检测及其故障诊断. E-mail:heyuling1@163.com 通信作者:付滋翔(2000—),男,华北电力大学在读硕士研究生,主要从事发电机设备状态检测及其故障诊断. E-mail:fuzixiang2023@163.com 第1期何玉灵等:轴向气隙非对称故障对发电机电磁转矩特性的影响河北大学学报(自然科学版) 第45卷generator under inclination eccentricity. The key operating parameters include the degree of inclination eccentricity and generation load differences. The whole work was carried out on a 5 kVA fault simulated generator and the results obtained from the theoretical and finite element analysis were verified through experiments. It is shown that the inclined eccentricity introduces an extra double frequency component to the electromagnetic torque and that both the DC component and the second frequency component of the electromagnetic torque increase as the eccentricity angle grow. In addition, as the load increases, the fluctuating characteristics of the generators electromagnetic torque will be increased, and both the DC component and the 2nd harmonic will be increased as well.
    Data driven solder layer state evaluation of IGBT module chip for converter valve
    HUANG Xiongfeng, DUAN Xiyao, HUANG Ming, CHEN Zhong, ZHU Lin, ZHANG Yujiao
    2025, 45(1):  10-19.  DOI: 10.3969/j.issn.1000-1565.2025.01.002
    Asbtract ( 59 )   PDF (1713KB) ( 48 )  
    References | Related Articles | Metrics
    Insulated gate bipolar transistor(IGBT)modules for converter valves are widely used in fields such as wind power transmission and grid interconnection. IGBT modules for converter valves have been widely used in wind power transmission and grid interconnection. As the operating time increases, the IGBT chip solder layer is prone to thermal fatigue damage, leading to a decrease in module reliability. Therefore, it is particularly critical to evaluate the state of the IGBT module chip solder layer. To this end, this paper proposes a data-driven method for evaluating the state of the IGBT module chip solder layer for converter valves. Firstly, the fatigue mechanism of the solder layer is analyzed, and evaluation parameters that can reflect the fatigue state of the chip solder layer are selected based on their ability to represent data and the ease of acquisition. Secondly, an electro-thermal coupling model of the IGBT module- DOI:10.3969/j.issn.1000-1565.2025.01.002基于数据驱动的换流阀用IGBT模块芯片焊料层状态评估黄雄峰1,段熙尧1,黄明1,陈忠2,祝琳2,张宇娇1(1.合肥工业大学 电气与自动化工程学院,功率半导体封装与可靠性安徽省重点实验室,安徽 合肥 230009;2.国网安徽省电力有限公司电力科学研究院,安徽 合肥 230601)摘 要:换流阀用绝缘栅双极型晶体管(IGBT)模块在风电输送与电网互联等领域得到广泛应用,随着运行时间的增长,IGBT芯片焊料层易发生热疲劳损伤,导致模块可靠性降低,因此实现IGBT模块芯片焊料层状态评估尤为关键.为此,提出一种基于数据驱动的换流阀用IGBT模块芯片焊料层状态评估方法.首先,分析焊料层的疲劳机理,并从数据的表征能力和获取难易程度出发,选取能够反映芯片焊料层疲劳状态的评估参数;其次,建立不同焊料层疲劳损伤状态的IGBT模块电热耦合模型,并通过有限元计算获得“疲劳状态-评估参数”数据;最后,考虑芯片焊料层疲劳状态与评估参数之间的非线性、相互交叉等问题,选取多种算法共同实现由评估参数到芯片焊料层的疲劳状态的映射,并对评估参数发展趋势进行预测.结果表明本评估方法准确性、实时性均满足工程需要,可为IGBT模块运维提供可靠依据.关键词:芯片焊料层;状态评估;数据驱动;评估参数;电热耦合模型 中图分类号:TP181 文献标志码:A 文章编号:1000-1565(2025)01-0010-10Data driven solder layer state evaluation of IGBT module chip for converter valveHUANG Xiongfeng1, DUAN Xiyao1, HUANG Ming1, CHEN Zhong2, ZHU Lin2, ZHANG Yujiao1(1.Anhui Province Key Laboratory of Semiconductor Packaging and Reliability, School of Electrical and Automation Engineering, Hefei University of Technology,Hefei 230009,China;2.Electric Power Research Institute,State Grid Anhui Electric Power Co., Ltd., Hefei 230601,China)Abstract: Insulated gate bipolar transistor(IGBT)modules for converter valves are widely used in fields such as wind power transmission and grid interconnection. IGBT modules for converter valves have been widely used in wind power transmission and grid interconnection. As the operating time increases, the IGBT chip solder layer is prone to thermal fatigue damage, leading to a decrease in module reliability. Therefore, it is particularly critical to evaluate the state of the IGBT module chip solder layer. To this end, this paper proposes a data-driven method for evaluating the state of the IGBT module chip solder layer for converter valves. Firstly, the fatigue mechanism of the solder layer is analyzed, and evaluation parameters that can reflect the fatigue state of the chip solder layer are selected based on their ability to represent data and the ease of acquisition. Secondly, an electro-thermal coupling model of the IGBT module- 收稿日期:2024-06-14;修回日期:2024-09-12 基金项目:安徽省自然科学基金资助项目(JZ2023GJDQ0018) 第一作者:黄雄峰(1980—),男,合肥工业大学副教授,博士,主要从事检测技术与自动化装置应用方向研究.E-mail: hfut_huangxf@hfut.edu.cn 通信作者:张宇娇(1978—),女,合肥工业大学教授,博士生导师,主要从事电气设备多物理场建模与仿真、基于数字孪生技术的电气设备故障诊断与健康寿命管理方向研究.E-mail: zhangyujiao@hfut.edu.cn 第1期黄雄峰等:基于数据驱动的换流阀用IGBT模块芯片焊料层状态评估河北大学学报(自然科学版) 第45卷with different fatigue damage states of the solder layer is established, and finite element calculations are performed to obtain ‘fatigue state-evaluation parameter data. Finally, considering the non-linearity and cross-correlation issues between the fatigue state of the chip solder layer and the evaluation parameters, multiple algorithms are selected to jointly achieve the mapping from the evaluation parameters to the fatigue state of the chip solder layer and predict the development trend of the evaluation parameters. The results show that the accuracy and real-time performance of this evaluation method can meet the engineering needs, providing a reliable basis for the operation and maintenance of IGBT modules.
    Dynamic compensation control of rotor voltage of doubly-fed wind turbine based on rotor transient current
    BAI Wangwang, ZHANG Zhongdan, ZHANG Yaozhong, ZHAO Weiyang, FU Yuan
    2025, 45(1):  20-33.  DOI: 10.3969/j.issn.1000-1565.2025.01.003
    Asbtract ( 57 )   PDF (2597KB) ( 43 )  
    References | Related Articles | Metrics
    Since the stator side of the doubly-fed induction generator(DFIG)is directly connected to the power grid and the rotor resistance value is usually small, the grid voltage symmetry fault leads to the rapid rise of DFIG rotor current, seriously affecting the grid-connected stability of wind turbines. Hence, this paper proposes a dynamic compensation scheme of rotor voltage based on the rotor transient current and analyzes the influence of the compensation scheme on the stator transient flux attenuation to address the problem that the converter cannot obtain the transient value directly and accurately compensate the rotor voltage for suppressing the rotor overcurrent when the power grid fails. The proposed method involves- DOI:10.3969/j.issn.1000-1565.2025.01.003基于转子暂态电流的双馈风电机组转子电压动态补偿控制白望望1,张中丹1,张耀忠1,赵伟阳1,付媛2(1.国网甘肃省电力公司经济技术研究院,甘肃 兰州 730050;2.华北电力大学 河北省分布式储能与微网省级重点实验室,河北 保定 071003)摘 要:双馈感应风力发电机(doubly-fed induction generator,DFIG)在电网发生对称故障后,因其定子侧直接与电网相连,且转子电阻阻值通常较小,电网电压对称故障将导致DFIG转子电流快速抬升,严重影响风电机组的并网稳定性.对于当电网发生故障后变流器无法直接快速准确获取暂态量来补偿转子电压以达到抑制转子过电流的问题,提出了一种基于转子暂态电流的转子电压动态补偿方案,并分析了该补偿方案对定子暂态磁链衰减的影响.首先对DFIG进行故障电路分析,得到转子绕组等效电路以及转子电流在电网电压对称跌落时的动态过程,并基于转子侧变流器的电流内环调节得到在同步旋转坐标系下的转子电流表达式.然后通过坐标变换与转子绕组等效电路参数,得到转子暂态感应电动势,将其通过前馈控制补偿转子侧变流器的输出电压,以此削弱转子过电流.仿真结果表明,基于转子暂态电流的转子电压动态补偿方案对转子过电流抑制有良好效果,所提的控制方案提高了DFIG在故障状态下的并网能力.关键词:双馈感应风力发电机;电网电压对称跌落;转子过电流;转子电压补偿;定子磁链衰减中图分类号:TM315 文献标志码:A 文章编号:1000-1565(2025)01-0020-14Dynamic compensation control of rotor voltage of doubly-fed wind turbine based on rotor transient currentBAI Wangwang1, ZHANG Zhongdan1, ZHANG Yaozhong1, ZHAO Weiyang1, FU Yuan21. Institute of Economic Technology, State Grid Gansu Electric Power Company, Lanzhou 730050, China; 2. Hebei Key Laboratory of Distributed Energy Storage and Micro-Grid, North China Electric Power University, Baoding 071003, China)Abstract: Since the stator side of the doubly-fed induction generator(DFIG)is directly connected to the power grid and the rotor resistance value is usually small, the grid voltage symmetry fault leads to the rapid rise of DFIG rotor current, seriously affecting the grid-connected stability of wind turbines. Hence, this paper proposes a dynamic compensation scheme of rotor voltage based on the rotor transient current and analyzes the influence of the compensation scheme on the stator transient flux attenuation to address the problem that the converter cannot obtain the transient value directly and accurately compensate the rotor voltage for suppressing the rotor overcurrent when the power grid fails. The proposed method involves- 收稿日期:2024-05-31;修回日期:2024-11-11 基金项目:国网甘肃省电力科技项目(522730230006) 第一作者:白望望(1991—),男,国网甘肃省电力公司经济技术研究院工程师,主要从事输电网规划技术及新能源消纳方向研究.E-mail:1241509352@qq.com 通信作者:付媛(1982—),女,华北电力大学副教授,博士,主要从事新能源发电控制技术方面的研究.E-mail:1172766364@qq.com 第1期白望望等:基于转子暂态电流的双馈风电机组转子电压动态补偿控制河北大学学报(自然科学版) 第45卷analyzing the fault circuit of the DFIG to derive the equivalent circuit of rotor winding and study the dynamic process of rotor current when the grid voltage drops symmetrically. Subsequently, the rotor overcurrent expression in the synchronous rotating coordinate system is obtained based on the current inner loop adjustment of the rotor side converter. Then, the rotor transient electromotive force(EMF)is obtained using coordinate transformation and equivalent circuit parameters of the rotor winding. This EMF is used by feedforward control to compensate the output voltage of the rotor-side converter, aiming to weaken the rotor overcurrent. Simulation results demonstrate that the dynamic compensation scheme based on transient rotor current for rotor voltage effectively suppresses rotor overcurrent, and the proposed control scheme enhances the grid connection capability of DFIG during power grid fault conditions.
    Carrier recombination processes in Sb2Se3 based on transient absorption spectroscopy
    FENG Bohao, DANG Wei, MO Anming, DONG Wenxin, LI Zhiqiang, ZHAO Xiaohui
    2025, 45(1):  34-42.  DOI: 10.3969/j.issn.1000-1565.2025.01.004
    Asbtract ( 53 )   PDF (1607KB) ( 50 )  
    References | Related Articles | Metrics
    Understanding the carrier recombination processes in Sb2Se3 is crucial for enhancing its optoelectronic performance. Femtosecond transient absorption spectroscopy(fs-TAS), with its high-resolution advantages, provides rich optical information and serves as a powerful tool for investigating carrier recombination processes in Sb2Se3. This study obtained broadband transient absorption spectra of polycrystalline Sb2Se3 thin films under different excitation wavelengths and excitation densities. It was first confirmed that the excited-state absorption signals in the 650—1 100 nm range on longer time scales(time delay greater than 10 ps)originated from deep-bound carrier absorption, while the excited-state signals in the 900—1 050 nm range on shorter time scales(time delay less than 10 ps)were attributed to shallow-bound carrier absorption. Through the transient absorption dynamics of Sb2Se3, this study extracted the lifetimes of the free carriers and the cooling time of the hot carriers. Under 950 nm excitation, the average lifetime of free carriers ranged from 35.28 to 54.23 ps and decreased with increasing- DOI:10.3969/j.issn.1000-1565.2025.01.004基于瞬态吸收光谱的Sb2Se3载流子复合过程冯博浩,党伟,莫安明,董汶鑫,李志强,赵晓辉(河北大学 物理科学与技术学院,河北省光电信息材料重点实验室,河北 保定 071002)摘 要:了解Sb2Se3中的载流子复合过程对提高其光电性能至关重要.飞秒瞬态吸收光谱(fs-TAS)凭借高分辨率的优点能够获得丰富的光学信息,是研究Sb2Se3载流子复合过程的有力工具.本文测得不同激发波长和激发密度下的多晶Sb2Se3薄膜的宽带瞬态吸收光谱.首先证实在长时间尺度下(时间延迟大于10 ps)探测光为650~1 100 nm激发态吸收信号源于深束缚载流子吸收作用,并将短时间尺度下(时间延迟小于10 ps)探测光为900~1 050 nm激发态信号归因于浅束缚载流子吸收.通过Sb2Se3的瞬态吸收动力学曲线,提取出其自由载流子寿命和热载流子冷却时间:在激发波长为950 nm条件下,自由载流子平均寿命为35.28~54.23 ps,随着激发密度增加而减小;在激发波长为550 nm和750 nm条件下,热载流子冷却时间为0.17~0.48 ps,与激发密度成正比.关键词:Sb2Se3;载流子复合;瞬态吸收光谱;自由载流子寿命;热载流子冷却 中图分类号:O472 文献标志码:A 文章编号:1000-1565(2025)01-0034-09Carrier recombination processes in Sb2Se3 based on transient absorption spectroscopy FENG Bohao, DANG Wei, MO Anming, DONG Wenxin, LI Zhiqiang, ZHAO Xiaohui(Hebei Provincial Key Laboratory of Optoelectronic Information Materials, College of Physics Science and Technology, Hebei University, Baoding 071002, China)Abstract: Understanding the carrier recombination processes in Sb2Se3 is crucial for enhancing its optoelectronic performance. Femtosecond transient absorption spectroscopy(fs-TAS), with its high-resolution advantages, provides rich optical information and serves as a powerful tool for investigating carrier recombination processes in Sb2Se3. This study obtained broadband transient absorption spectra of polycrystalline Sb2Se3 thin films under different excitation wavelengths and excitation densities. It was first confirmed that the excited-state absorption signals in the 650—1 100 nm range on longer time scales(time delay greater than 10 ps)originated from deep-bound carrier absorption, while the excited-state signals in the 900—1 050 nm range on shorter time scales(time delay less than 10 ps)were attributed to shallow-bound carrier absorption. Through the transient absorption dynamics of Sb2Se3, this study extracted the lifetimes of the free carriers and the cooling time of the hot carriers. Under 950 nm excitation, the average lifetime of free carriers ranged from 35.28 to 54.23 ps and decreased with increasing- 收稿日期:2024-04-13;修回日期:2024-05-07 基金项目:国家自然科学基金资助项目(12275065);中央引导地方科技发展资金资助项目(236Z4305G);河北省光电信息材料重点实验室项目(22567634H) 第一作者: 冯博浩(1999—),男,河北大学在读硕士研究生,主要从事半导体载流子复合动力学方向研究.E-mail: 13373111085@163.com 通信作者: 赵晓辉(1978—),男,河北大学副教授,主要从事半导体载流子复合动力学方向研究.E-mail: xhzhao@hbu.edu.cn 第1期冯博浩等:基于瞬态吸收光谱的Sb2Se3载流子复合过程河北大学学报(自然科学版) 第45卷excitation density. Under 550 nm and 750 nm excitation, the time constant of hot carrier cooling times was in range of 0.17—0.48 ps and was proportional to the excitation density.
    Surface modification of polypropylene and polyester by a coaxial perforated inner electrode dielectric barrier discharge
    WANG Yun, WANG Weiwei, FAN Zhihui, LIU Feng, SHI Guihu, WANG Jingquan
    2025, 45(1):  43-49.  DOI: 10.3969/j.issn.1000-1565.2025.01.005
    Asbtract ( 48 )   PDF (1287KB) ( 35 )  
    References | Related Articles | Metrics
    In order to improve the application effect of plasma on the surface treatment of polymer materials, a coaxial perforated inner electrode dielectric barrier discharge reactor is proposed in this paper, and the experimental results show that the structure of the perforated inner electrode has higher discharge power, which can make the contact angle drop lower in a shorter period of time. The reactor generates plasma for surface modification of polypropylene and polyester, and the surface contact angle is reduced from 90° to 40° and from 88° to 30°, respectively. The effectiveness of the plasma treatment is increased by employing three working gases: helium, argon and air. This study has practical value in industrial applications and provides a reference for improving the surface hydrophilicity of polymer materials.
    Schiff base reaction-induced fluorescence quenching of carbon dots for detection of formaldehyde
    CHANG Zhiwei, LIU Xiaotong, WANG Shoulin, YANG Yang, SHEN Shigang, DONG Jiangxue
    2025, 45(1):  50-59.  DOI: 10.3969/j.issn.1000-1565.2025.01.006
    Asbtract ( 68 )   PDF (1740KB) ( 33 )  
    References | Related Articles | Metrics
    In this work, the yellow fluorescent carbon dots(o-PD-CDs)was prepared by the microwave assisted method with o-phenylenediamine(o-PD)and N,N-dimethylformamide as raw materials, the preparation method is simple and rapid. Further study found that the yellow emission of o-PD-CDs would be quenched by formaldehyde(FA)in aqueous solution, and the quenching value of fluorescence intensity showed a good liner relationship with the FA concentration in the range from 0.01 to 0.80 mg/L, therefore, a fluorescent sensor was constructed for the quantitative detection of FA in aqueous solution and the limit of detection was 5.2 μg/L. Moreover, the FA sensing mechanism was explored, and the results showed that the o-PD-CDs possessed a lot of amino groups on the surface, a Schiff base reaction- DOI:10.3969/j.issn.1000-1565.2025.01.006席夫碱反应诱导的荧光碳点猝灭用于检测甲醛常志伟1,刘晓彤1,王守林1,杨阳1,申世刚1,2,董江雪1(1.河北大学 化学与材料科学学院,河北 保定 071002;2.京津冀(雄安新区)生态安全与生态保护教育部工程研究中心,河北 保定 071002)摘 要:以富含碳元素和氮元素的邻苯二胺和N,N-二甲基甲酰胺为原料,在微波辅助下通过一锅法成功制备了发射黄色荧光的碳点(o-PD-CDs),该制备方法简单快速.实验发现,所制备碳点的黄色荧光在水溶液中可被甲醛(FA)猝灭,并在FA质量浓度为0.01~0.80 mg/L时,荧光强度猝灭值与FA质量浓度呈现较好的线性关系.以o-PD-CDs为探针构建了水溶液中定量检测FA的荧光传感器,最低检出限为5.2 μg/L.此外,对检测FA的传感机制进行了研究,表明o-PD-CDs 含有丰富的氨基,可与FA发生席夫碱反应并生成相应的亚胺,从而导致 o-PD-CDs 的荧光发生猝灭.进一步实验发现,随着FA含量的增加,溶液中出现明显的席夫碱沉淀,据此可以实现质量浓度在0.5~150 mg/mL内FA的可视化半定量检测.所建立的传感器已成功应用于食品样品中甲醛的测定,回收率为98.10%~ 107.86%,相对标准偏差为0.86%~2.71%.关键词:碳点;荧光传感器;甲醛检测;席夫碱反应中图分类号:O657.1 文献标志码:A 文章编号:1000-1565(2025)01-0050-10Schiff base reaction-induced fluorescence quenching of carbon dots for detection of formaldehydeCHANG Zhiwei1, LIU Xiaotong1, WANG Shoulin1, YANG Yang1, SHEN Shigang1,2, DONG Jiangxue1(1. College of Chemisitry and Materials Science, Hebei University, Baoding 071002, China; 2. Engineering Research Center of Ecological Safety and Conservation in Beijing-Tianjin-Hebei(Xiongan New Area)of MOE, Baoding 071002, China)Abstract: In this work, the yellow fluorescent carbon dots(o-PD-CDs)was prepared by the microwave assisted method with o-phenylenediamine(o-PD)and N,N-dimethylformamide as raw materials, the preparation method is simple and rapid. Further study found that the yellow emission of o-PD-CDs would be quenched by formaldehyde(FA)in aqueous solution, and the quenching value of fluorescence intensity showed a good liner relationship with the FA concentration in the range from 0.01 to 0.80 mg/L, therefore, a fluorescent sensor was constructed for the quantitative detection of FA in aqueous solution and the limit of detection was 5.2 μg/L. Moreover, the FA sensing mechanism was explored, and the results showed that the o-PD-CDs possessed a lot of amino groups on the surface, a Schiff base reaction- 收稿日期:2024-08-10;修回日期:2024-09-30 基金项目:河北省自然科学基金资助项目(B2024201050);河北大学研究与创新团队项目(IT2023A03);河北大学实验室开放项目(sy202217) 第一作者:常志伟(1999-),男,河北大学在读硕士研究生,主要从事食品安全评估与检验.E-mail:18855216698@163.com 通信作者:董江雪(1987-),女,河北大学副教授,博士,主要从事纳米传感器研究.E-mail:dongjxue@163.com申世刚(1964-),男,河北大学教授,博士,主要从事食品与环境分析研究.E-mail:shensg@hbu.edu.cn 第1期常志伟等:席夫碱反应诱导的荧光碳点猝灭用于检测甲醛河北大学学报(自然科学版) 第45卷would occur between the amino groups and FA, which led to the fluorescence quenching of o-PD-CDs. In addition, with the increase of FA concentration, the Schiff base precipitated obviously in the solution, and the visual semi-quantitative detection of FA in the range of 0.5—150 mg/mL could be realized. The established sensor has been successfully applied to the determination of FA in food samples with the recovery rate of 98.1%—107.86% and the relative standard deviations of 0.86%—2.71%.
    Perfluorosulfonic acid resin modified ZSM-5 zeolite as catalyst for cyclohexene hydration
    NIU Libo, XUE Yulian, ZHANG Qian, WANG Yatao, XU Zhaozhong, CHEN Yi, LYU Yunkai
    2025, 45(1):  60-69.  DOI: 10.3969/j.issn.1000-1565.2025.01.007
    Asbtract ( 43 )   PDF (1563KB) ( 26 )  
    References | Related Articles | Metrics
    A series xHNF/ZSM-5(where x represents the mass fraction of sulfonic acid resin in the catalyst)composite catalysts were prepared by loading perfluorosulfonic acid resin on ZSM-5 using the impregnation method and applied in the hydration of cyclohexene to produce cyclohexanol. The physicochemical properties of corresponding catalysts were studied by BET, XRD, TEM, and Py-IR. In addition, the influence of reaction condition was also investigated in this work. It was found that with reaction temperature of 125 ℃, 0.4 MPa of nitrogen pressure and the reaction time of 120 min, a 12.9% cyclohexene conversion with the selectivity of cyclohexanol over 99% could achieved with 20HNF/ZSM-5, which is the optimal catalyst in this reaction. Meanwhile, the conversion rate of cyclohexene remained above 10% for the 20HNF/ZSM-5 catalyst with five cycles, indicating its excellent stability during reaction.
    Intervention effects of BJJP on the proliferation, apoptosis, and EMT of PANC-1 pancreatic cancer cells
    XIONG Yanan,LI Yiheng,ZHANG Ronghua,ZHANG Guangling,LIU Zhiyong
    2025, 45(1):  70-81.  DOI: 10.3969/j.issn.1000-1565.2025.01.008
    Asbtract ( 54 )   PDF (3061KB) ( 33 )  
    References | Related Articles | Metrics
    To investigate the effects of BJJP on the proliferation, apoptosis, and EMT of PANC-1 pancreatic cancer cells.CCK-8, Colony formation, Western blot, TUNEL scratch, Transwell and immunofluorescence assays were used to detect the effect of BJJP-containing serum on the activity of human normal pancreatic ductal epithelial cells HPNE, and detect the effects of BJJP-containing serum on the proliferation, apoptosis, migration, invasion, EMT, and the protein expression of PI3K/AKT pathway of pancreatic cancer cells PANC-1. The results showed that BJJP-containing serum has no significant effect on the activity of HPNE cells but inhibits the proliferation, migration, invasion, EMT- DOI:10.3969/j.issn.1000-1565.2025.01.008鳖甲煎丸对胰腺癌细胞PANC-1增殖、凋亡和EMT的干预作用熊亚南1,李以恒1,张荣花1,章广玲2,刘志勇2(1.华北理工大学 基础医学院, 河北省慢性疾病重点实验室, 河北 唐山 063210;2.华北理工大学附属医院,河北省医工融合精准医疗重点实验室, 河北 唐山 063000)摘 要:为探讨鳖甲煎丸(biejiajian pill,BJJP)对胰腺癌细胞增殖、凋亡和上皮-间充质转化(EMT)的干预作用.采用CCK-8、集落形成、Western blot、TUNEL划痕、Transwell和免疫荧光等实验方法检测BJJP含药血清对人正常胰腺导管上皮细胞HPNE活力的影响,对胰腺癌细胞PANC-1增殖、凋亡、迁移、侵袭、EMT以及PI3K/AKT通路蛋白表达的影响.结果显示:BJJP含药血清对HPNE细胞的活力无明显影响,具有抑制PANC-1细胞的增殖、迁移、侵袭、EMT进程的能力,促进了PANC-1细胞凋亡,抑制了PI3K/AKT通路,综上,鳖甲煎丸能抑制胰腺癌PANC-1细胞的恶性生物学行为,其机制可能与调节PI3K/AKT通路有关.关键词:鳖甲煎丸;胰腺癌;增殖;凋亡;上皮-间充质转化中图分类号:R735.9 文献标志码:A 文章编号:1000-1565(2025)01-0070-12Intervention effects of BJJP on the proliferation, apoptosis, and EMT of PANC-1 pancreatic cancer cellsXIONG Yanan1,LI Yiheng1,ZHANG Ronghua1,ZHANG Guangling2,LIU Zhiyong2(1. Hebei Key Laboratory for Chronic Diseases, School of Basic Medicine, North China University of Science and Technology, Tangshan 063210, China; 2. Hebei Provincial Key Laboratory of Medical-Industrial Integration Precision Medicine, North China University of Science and Technology Affiliated Hospital, Tangshan 063000, China)Abstract: To investigate the effects of BJJP on the proliferation, apoptosis, and EMT of PANC-1 pancreatic cancer cells.CCK-8, Colony formation, Western blot, TUNEL scratch, Transwell and immunofluorescence assays were used to detect the effect of BJJP-containing serum on the activity of human normal pancreatic ductal epithelial cells HPNE, and detect the effects of BJJP-containing serum on the proliferation, apoptosis, migration, invasion, EMT, and the protein expression of PI3K/AKT pathway of pancreatic cancer cells PANC-1. The results showed that BJJP-containing serum has no significant effect on the activity of HPNE cells but inhibits the proliferation, migration, invasion, EMT- 收稿日期:2024-06-12;修回日期:2024-09-14 基金项目:河北省自然科学基金资助项目(H2023209047;H202409077);河北省教育厅在读研究生创新能力培养项目(CXZZSS2024056) 第一作者:熊亚南(1978—),女,华北理工大学副教授,主要从事胰腺癌分子机制研究.E-mail:xiongyanan@ncst.edu.cn 通信作者:刘志勇(1971—),男,华北理工大学教授,博士,主要从事胰腺癌分子机制研究.E-mail:macromicro@126.com 第1期熊亚南等:鳖甲煎丸对胰腺癌细胞PANC-1增殖、凋亡和EMT的干预作用河北大学学报(自然科学版) 第45卷process and PI3K/AKT pathway, enhances the apoptosis of pancreatic cancer PANC-1 cells.Studies have shown that BJJP inhibits the malignant biological behavior of pancreatic cancer PANC-1 cells, and the mechanism may be related to the regulation of PI3K/AKT pathway.
    Bioinformatics analysis of SiNF-YA subfamily genes and drought resistance gene mining in Setaria italica
    WANG Chunfang, ZHANG Peihan, SHI Shenkui, YANG Jiayi, WANG Yufang, QI Dongmei
    2025, 45(1):  82-90.  DOI: 10.3969/j.issn.1000-1565.2025.01.009
    Asbtract ( 51 )   PDF (1197KB) ( 21 )  
    References | Related Articles | Metrics
    To explore the function of SiNF-YA subfamily genes in Setaria italica. Firstly, the bioinformatics of 10 members of the SiNF-YA subfamily genes in foxtail millet were analyzed by using several online websites. Secondly, Ubuntu system and RStudio software were used for haplotype analysis of SiNF-YA subfamily genes. At last, through analysis of transcriptome data, the expression of SiNF-YA5 in different tissues of drought-sensitive and drought-tolerant varieties was investigated. The results showed that SiNF-YA subfamily genes of foxtail millet were distributed on four chromosomes, mainly located in the nucleus and extracellular secretion. The cis-acting elements related to abiotic stress response were distributed in the promoter region. Meanwhile, the subfamily genes were strongly correlated with drought resistance. In addition, the expression of SiNF-YA5 was detected before and after PEG treatment. There were significant differences between leaf and root expression levels. This study provide - DOI:10.3969/j.issn.1000-1565.2025.01.009谷子SiNF-YA亚家族基因的生物信息学分析与抗旱基因挖掘王春芳1,张霈涵2,史慎奎1,杨佳怡2,王玉芳1,祁东梅1(1.河北民族师范学院 生物与食品科学学院,冀北山区杂粮产业协同创新中心,河北 承德 067000;2.河北师范大学 生命科学学院,河北 石家庄 050024)摘 要:为探究谷子(Setaria italica)SiNF-YA亚家族基因的功能,首先,利用多个在线网站对谷子10个SiNF-YA亚家族基因进行了相关的生物信息学分析;其次,利用Ubuntu系统和RStudio软件对谷子SiNF-YA基因进行单倍型分析;最后,通过对转录组数据的分析,探究谷子SiNF-YA5亚家族基因在干旱敏感品种、耐旱品种各组织中的表达量差异.结果表明,谷子SiNF-YA亚家族基因分布在4条染色体上,主要定位于细胞核和胞外分泌中,其启动子区含有与非生物胁迫响应相关的顺式作用元件.同时该基因亚家族成员与抗旱性具有很强的相关性,并且谷子SiNF-YA5亚家族基因在PEG处理前后,叶片和根部的表达量具有显著性差异.本研究为谷子抗旱品种的育种提供理论支持.关键词:谷子;SiNF-YA亚家族基因;抗旱;生物信息学分析;单倍型分析中图分类号:S515 文献标志码:A 文章编号:1000-1565(2025)01-0082-09Bioinformatics analysis of SiNF-YA subfamily genes and drought resistance gene mining in Setaria italicaWANG Chunfang1, ZHANG Peihan2, SHI Shenkui1, YANG Jiayi2, WANG Yufang1, QI Dongmei1(1. Collaborative Innovation Center of Minor Cereals Industry in North Hebei, College of Biological and Food Science,Hebei Minzu Normal University, Chengde 067000,China; 2. College of Life Science, Hebei Normal University, Shijiazhuang 050024,China)Abstract: To explore the function of SiNF-YA subfamily genes in Setaria italica. Firstly, the bioinformatics of 10 members of the SiNF-YA subfamily genes in foxtail millet were analyzed by using several online websites. Secondly, Ubuntu system and RStudio software were used for haplotype analysis of SiNF-YA subfamily genes. At last, through analysis of transcriptome data, the expression of SiNF-YA5 in different tissues of drought-sensitive and drought-tolerant varieties was investigated. The results showed that SiNF-YA subfamily genes of foxtail millet were distributed on four chromosomes, mainly located in the nucleus and extracellular secretion. The cis-acting elements related to abiotic stress response were distributed in the promoter region. Meanwhile, the subfamily genes were strongly correlated with drought resistance. In addition, the expression of SiNF-YA5 was detected before and after PEG treatment. There were significant differences between leaf and root expression levels. This study provide - 收稿日期:2024-06-12;修回日期:2024-08-24 基金项目: 承德市基础研究项目(202305B093);河北民族师范学院青年基金项目(QN2019003) 第一作者:王春芳(1983—),女,河北民族师范学院副教授,博士,主要从事谷子分子育种方面的研究.E-mail:wangchunfang18@126.com 通信作者:祁东梅(1990—),女,河北民族师范学院讲师,博士,主要从事谷子功能基因方面的研究.E-mail: dmqikaka@163.com 第1期王春芳等:谷子SiNF-YA亚家族基因的生物信息学分析与抗旱基因挖掘河北大学学报(自然科学版) 第45卷theoretical support for functional verification of subsequent SiNF-YA gene subfamilies and breeding of foxtail millet varieties with drought resistance.
    Construction method of microblog user interest profile based on content preference and emotional tendency
    XU Jianmin,WANG Mingyu
    2025, 45(1):  91-103.  DOI: 10.3969/j.issn.1000-1565.2025.01.010
    Asbtract ( 61 )   PDF (1479KB) ( 26 )  
    References | Related Articles | Metrics
    The explosive growth of microblogging data makes information screening increasingly difficult.Constructing a reasonable microblog user interest profile helps to achieve accurate service and improve recommendation performance. First, the LDA(latent Dirichlet allocation)model is used to excavate the users content preference characteristics from the users historical content,and the corresponding emotional tendency in the users different content preferences is calculated by the emotional analysis model, so as to obtain the users interest profile containing two dimensions of content preferences and their corresponding emotional tendencies. When evaluating microblog recommendations based on user interest profile, where the users content preferences are used for the initial screening first to see whether the content of the blog post matches with the users content preference. And if they match each other, the algrithm would further filters the blog posts by emotional tendency, compares their emotional similarity under the same content preference, and select the blog posts above the threshold to add into the recommendation set. The experimental results on the real microblog dataset show that the microblog recommendation- DOI:10.3969/j.issn.1000-1565.2025.01.010基于内容偏好和情绪倾向的微博用户兴趣画像构建方法徐建民,王铭宇(河北大学 网络空间安全与计算机学院,河北 保定 071000)摘 要:微博数据的爆炸式增长,使信息筛选变得越来越困难.构建合理的微博用户兴趣画像,有助于实现精准化服务,提高推荐性能.首先,利用LDA(latent Dirichlet allocation)模型从用户历史内容中挖掘用户的内容偏好特征,并通过情绪分析模型计算用户不同内容偏好对应的情绪倾向,得到包含内容偏好及其对应情绪倾向2个维度的用户兴趣画像;在基于用户兴趣画像进行微博推荐评估时,利用用户内容偏好进行初步筛选,比较待评估博文内容与用户的内容偏好是否匹配,若匹配则进一步通过情绪倾向进行过滤,比较同一内容偏好下的情绪相似度,选取高于阈值的博文加入推荐集.真实微博数据集的实验结果表明,与基于标签的推荐模型、基于情感关联规则的推荐模型和基于主题的推荐模型相比,本文微博推荐方法具有更好的性能,在F1值上分别提升了10%、6%和2%.关键词:用户兴趣画像;内容偏好;情绪倾向;微博推荐中图分类号:TP391.3 文献标志码:A 文章编号:1000-1565(2025)01-0091-13Construction method of microblog user interest profile based on content preference and emotional tendencyXU Jianmin,WANG Mingyu(School of Cyber Security and Computer, Hebei University, Baoding 071000, China)Abstract: The explosive growth of microblogging data makes information screening increasingly difficult.Constructing a reasonable microblog user interest profile helps to achieve accurate service and improve recommendation performance. First, the LDA(latent Dirichlet allocation)model is used to excavate the users content preference characteristics from the users historical content,and the corresponding emotional tendency in the users different content preferences is calculated by the emotional analysis model, so as to obtain the users interest profile containing two dimensions of content preferences and their corresponding emotional tendencies. When evaluating microblog recommendations based on user interest profile, where the users content preferences are used for the initial screening first to see whether the content of the blog post matches with the users content preference. And if they match each other, the algrithm would further filters the blog posts by emotional tendency, compares their emotional similarity under the same content preference, and select the blog posts above the threshold to add into the recommendation set. The experimental results on the real microblog dataset show that the microblog recommendation- 收稿日期:2024-09-19;修回日期:2024-11-05 基金项目:国家社会科学基金资助项目(23BTQ092) 第一作者:徐建民(1966—),男,河北大学教授,博士生导师,主要从事信息检索方向研究.E-mail:hbuxjm@hbu.edu.cn 通信作者:王铭宇(1997—),男,河北大学在读硕士研究生,主要从事微博推荐方向研究.E-mail:yu668135@163.com 第1期徐建民等:基于内容偏好和情绪倾向的微博用户兴趣画像构建方法河北大学学报(自然科学版) 第45卷method in this paper has better performance compared with the label-based recommendation model, sentiment association rule-based recommendation model and topic-based recommendation model, with 10%, 6% and 2% improvement in the F1 value, respectively.
    Optimization method of process parameters of composite molding
    YANG Zeqing,DU Jingxuan,HU Ning,ZHANG Yanxing,JIN Yi
    2025, 45(1):  104-112.  DOI: 10.3969/j.issn.1000-1565.2025.01.011
    Asbtract ( 56 )   PDF (1017KB) ( 20 )  
    References | Related Articles | Metrics
    Aiming at the problems of high energy consumption, low production efficiency and unstable product quality of traditional molding process, the adaptive genetic algorithm was proposed to optimize the multi-parameters of holding time, molding pressure and temperature in the molding process. And the molding pressure, holding time and temperature of process data obtained by experiments are taken as input layer neurons, and the warping deformation of molding mass is taken as output layer neurons. BP neural network was constructed to obtain the functional relationship between warping deformation and molding pressure, holding time and temperature. Then adaptive genetic algorithm is used to optimize multiple process parameters. After the steps of binary coding, selection, crossover and mutation, the optimized results were obtained. The results show that the adaptive genetic algorithm can improve the warping deformation caused by the imbalance of holding time, molding pressure and temperature in the molding process, and improve the molding quality of the product.